Learn how to replace the ENTIRE front suspension of your car in this two episode series. First I will show you how to remove the wheel bearing, ball joints, control arms, tie rod, strut, and axle.

The ball joint and wheel bearing has to be pressed out of the knuckle and I have a bunch of tips and tricks to make that easy. The upper control arm ball joint and tie rod can get stuck in the knuckle so I show some tricks on how to easily remove that. The rest of the suspension parts are pretty simple to remove and replace.

NEXT EPISODE: automobilrevue.net/v/Vl9nMS1XSEQ0cnc

Tools and Products:
Mevotech Suspension Parts: amzn.to/2VKrmfr
Rust Paint: amzn.to/2Dg5yAV
Impact gun: amzn.to/2It3KIo
Torque Wrench: amzn.to/2UO2yFY
Bearing Press: amzn.to/2Gh8tv3
Ball Joint Puller: amzn.to/2P2wmcH
Slide Hammer: amzn.to/2URoqAe
Ball Joint Press: amzn.to/2UTxEvR
4lb Hammer: amzn.to/2GhZ06A
Vice: amzn.to/2IfqPyV

→ Become a ChrisFix Subscriber: www.youtube.com/subscription_center?add_user=paintballoo7
→ Instagram: www.instagram.com/chrisfixit
→ Facebook: www.facebook.com/chrisfix8
→ Website: www.ChrisFixed.com
→ My Channel Home Page: www.youtube.com/ChrisFix

**If the video was helpful, remember to give it a "thumbs up" and consider subscribing.**

Disclaimer:
Due to factors beyond the control of ChrisFix, I cannot guarantee against improper use or unauthorized modifications of this information. ChrisFix assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ChrisFix recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ChrisFix, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ChrisFix.

Comments

    • ChrisFix
      ChrisFix

      Did you guys get notified by YouTube that the video was posted? Also when you watched the video, was there a screen that said "this video was flagged by the YouTube community and may be offensive" or something like that? Just wanted to check because I had issues last night which is why I had to postpone publishing the video. I hope it's all fixed and you guys learn a lot from the video! Stay tuned for the next video and then for a video that, well, covers a life changing event ;)
      Also for those asking why I am wondering, here is what happened last night when I went to publish: https://www.instagram.com/p/BwI-VOhFkt2/

      about 3 months ago
    • This Old Chevy
      This Old Chevy In reply to ChrisFix

      ChrisFix is your “thick black paint” KBS coating?

      about 17 hours ago
    • This Old Chevy
      This Old Chevy In reply to ChrisFix

      ChrisFix “all you need for tools is.... *proceeds to show off 10k of stuff*

      about 17 hours ago
    • Erik Johnson
      Erik Johnson In reply to ChrisFix

      I’m offended by the fact that I only discovered your channel this year. Your YouTube channel is #1 for me. I can’t thank you enough. Totally inspired.

      I went through some deep depression this year. Your videos renewed my zest for life. I’m eternally in your debt.

      Sorry to get all deep! But you’re helping people in ways you might not even know.

      about 6 days ago
    • KSP Guy
      KSP Guy In reply to ChrisFix

      No nothting

      about 10 days ago
    • RedNinja
      RedNinja In reply to ChrisFix

      No surprisingly nothing at all

      about 12 days ago
    • A—N—I—M—E —T
      A—N—I—M—E —T

      This is gonna inspire me to be a mechanic or just fix cars if I want to if I have time

      about 2 hours ago
    • slavapal00za
      slavapal00za

      Amazing video! All of the different parts in the wheel well and how they work together were somewhat of a mystery to me...until now! You do such a great job explaining as you are demonstrating. I really like that you work on vehicles that present real challenges someone may face, like the hub not pulling out initially, and how to overcome them. Great work! I really appreciate it 😁👍

      about 4 hours ago
    • Mr Haych
      Mr Haych

      Great job, i replaced a rear wheel bearing on bmw. I had one issue which no one has covered on youtube. When i removed the hub, the casing of the bearing which covers the balls was stuck on the hub, so when i took the old bearing out and put the new one in, the hub wasn't going in all the way. After 1 whole day, i realsied that i needed to take the bearing cover off the hub. In this case it was too difficult so i took the casing off the new bearing and used the casing for the previous bearing.

      about 19 hours ago
    • Solverz
      Solverz

      You should show us how to replace a sub frame 😏

      about 1 day ago
    • Wertosh Naminus
      Wertosh Naminus

      19:20 ...the hacksaw on the screw was a good idea. Before doing that, I would have hit the screws with some penetrant then a small wire brush in hopes to seat that bit more into the void.
      I don’t know any other Canadians who hate slotted screws more than I do, haha.

      Keep up the great work.

      about 1 day ago
    • Rex Holes
      Rex Holes

      What no soap and wooder?

      about 1 day ago
    • kosmo seedo
      kosmo seedo

      Thats a big fix right there. CF

      about 1 day ago
    • Nigel Foster
      Nigel Foster

      He makes this look so easy...

      about 2 days ago
    • Jestone Walker
      Jestone Walker

      At 7:08 i just laugh 😂😂😂😂😂😂😂 . You have a strong hands. It look you are professional removing the hub .That good Chris

      about 2 days ago
    • Jankis Janki
      Jankis Janki

      rb26 swap ?

      about 2 days ago
    • Timmy C
      Timmy C

      Hey Chris I have a question? What’s the difference between a impact drill and a normal drill?

      about 2 days ago
    • TheSaxAppeal
      TheSaxAppeal

      "With these nuts removed --"
      Your dog would like to know your location

      about 2 days ago
    • John Chaparro
      John Chaparro

      I don’t wanna sound like a Dumbass but can I “replace” the “rear suspension”

      about 2 days ago
    • Jiggajig Jones
      Jiggajig Jones

      Sweerrpaaaaaa

      about 2 days ago
    • Jay Damm
      Jay Damm

      13:44 Chris: it wasn't that hard, see how simple it was
      Me: how tf he do that without rethinking himself

      about 2 days ago
    • Jay Damm
      Jay Damm In reply to Jay Damm

      Sadly I'm 14 so I'll be waiting a couple years

      about 2 days ago
    • Todd Clay
      Todd Clay

      How do you know if parts meet or exceed OEM? Why not just replace the knuckle too?

      about 3 days ago
    • MrMuffinsandTwinkies
      MrMuffinsandTwinkies

      Man how the hell did you remove that axle so easily. On that badly of a rusted vehicle? The hell am I doing wrong lol. Axle slide hammer kit, chain+sludge hammer, pry bars and kicking them. Nothing is allowing mine to just 'pop out'. I swear this car is possessed.

      about 3 days ago
    • MrMuffinsandTwinkies
      MrMuffinsandTwinkies In reply to MrMuffinsandTwinkies

      @Josh I did

      about 6 hours ago
    • Josh
      Josh In reply to MrMuffinsandTwinkies

      The magic of video editing. Use a blowtorch if you must.

      about 6 hours ago
    • beards & bucks
      beards & bucks

      Did you sell it and how much

      about 3 days ago
    • Celestina Martinez
      Celestina Martinez

      Do need a need Axul if i hear a click when i turn when accelerating

      about 3 days ago
    • Saša Duran
      Saša Duran

      That is not rebuilding, that is replacing. You said it too.

      about 3 days ago
    • Kabooki San
      Kabooki San

      Woo! for del sol! Booo! for S trim :p

      about 3 days ago
    • Munchy
      Munchy

      Do more videos on the Honda del sol!

      about 3 days ago
    • MUHAMMAD ASHIQ HUSSAIN
      MUHAMMAD ASHIQ HUSSAIN

      Are you going to take this Honda to drifting?

      about 3 days ago
    • EJSFilms2K
      EJSFilms2K

      I think ChrisFix is really HowToBasic

      about 4 days ago
    • Taylor Smith
      Taylor Smith

      YOU ACTUALLY DROVE THAT WTH

      about 4 days ago
    • Sukha saini
      Sukha saini

      Good bro. ..we grab too much information

      about 5 days ago
    • Dayton Larson
      Dayton Larson

      Dude... You are actually a genius. All your little tricks would have saved me YEARS OF MY LIFE!

      about 5 days ago
    • Mr Alexander
      Mr Alexander

      Great video bud. Fantastic explanations very well said and straight forward and clear. Very professional

      about 5 days ago
    • Cranberry
      Cranberry

      You should save up to get your driveway and garage redone and start doing vids in there love the content keep it up ❤️❤️❤️

      about 5 days ago