Finally I get my WPL C34km. It's on another level for sure! WPL is always making better and better kit. Hope you enjoy and we will see how WPL progresses and what they come out with next!

C34km:
30a esc
Flysky gt3c tx/rx

Comments

    • Patrick van Luinen
      Patrick van Luinen

      Can i use the motormout for the c34 on the c24 ?

      about 10 days ago
    • RunThatRC
      RunThatRC In reply to Patrick van Luinen

      You can mount the c34km motor on the c24 but finding the right length driveshafts is the only problem.

      about 8 days ago
    • Rafael Schimuneck
      Rafael Schimuneck

      I would like to know how did you put the receiver and the ESC in the front space.

      about 17 days ago
    • RunThatRC
      RunThatRC In reply to Rafael Schimuneck

      Haha very careful stuffing and squishing lol. It's the small cheap 30a esc that most people put in these. It's a tight fit that required me to screw it together while holding it sandwiched. Its tricky but doable.

      about 17 days ago
    • Tonys Rc Tech
      Tonys Rc Tech

      Fantastic review on that Kit, its something to think about, great video, thanks for sharing 👍😀👍

      about 1 month ago
    • XD40Lou's RC Channel Lou's RC Garage
      XD40Lou's RC Channel Lou's RC Garage

      Good job on review I have been considering this rig.😎😎😎
      Thanks subbed 👍👍 actually I think it will be my next truck next month

      about 1 month ago
    • Bradley RC
      Bradley RC

      Love wpl ! Looking to get a kit version.👍👊

      about 1 month ago
    • Louis & Pamela Hedges
      Louis & Pamela Hedges

      There cheap enough to make them the way you want and that's the best part and ur right everyone has their own way
      wize words my friend
      No hate nothing but love for the rc boat plane car drone submarine helicopter even the flying fish love that RC

      about 1 month ago
    • RunThatRC
      RunThatRC In reply to Louis & Pamela Hedges

      🤣 I love the flying fish/shark!

      about 1 month ago
    • Louis & Pamela Hedges
      Louis & Pamela Hedges

      Awesome awesome awesome man now the real deal the real ?
      MN 45 or wpl c34 for me I want both ps love the shirt

      about 1 month ago
    • RunThatRC
      RunThatRC In reply to Louis & Pamela Hedges

      The mn45 kit isn't bad really. Just a little upgrades and its ready to go. It has its upsides. The WPL C34km is on another level. I say get both😈! LoL

      about 1 month ago
    • RC iloilo
      RC iloilo

      Hehe kuya this is my personal account now i am rc ph remember? 🤔🤔😁

      about 1 month ago
    • RunThatRC
      RunThatRC In reply to RC iloilo

      Nice!

      about 1 month ago
    • RC Journey
      RC Journey

      ☢️ Nice video. Your hilarious. Great thoughts. Hopefully we can buy a chassis kit no body🤩.

      about 1 month ago
    • RunThatRC
      RunThatRC In reply to RC Journey

      That would be nice. They should offer some bodies. Even some lexan ones. It would improve the performance for sure!

      about 1 month ago
    • Vino Veritas
      Vino Veritas

      What if i put inside ESC which is 3S capable, is it smart to run it on 3S battery, will gears and other things handle speed and torque?
      Is it included motor 6V or 12V?
      So i'm wondering, if instead of 2 speds gearbox put inside 12V motor and run it on 3S, will get a same speed and torque like on 2 speed gearbox and 2S battery, what do you think?

      about 1 month ago
    • Vino Veritas
      Vino Veritas In reply to Vino Veritas

      Thank you very much for reply, will try to install 12V motor and run it on 3S when i get my kit and i'm looking forward to see your video running it on 2 speed gearbox.

      about 1 month ago
    • RunThatRC
      RunThatRC In reply to Vino Veritas

      Not sure of the specs of the included motor. But if you are able to install a 12v motor I think the rest of the parts will handle it. I have one that's running brushless with a plastic geared 2speed and metal op parts upgrade. That has been reliable so far. I have a bunch of 2s lipos so I do the 2 speed route. I do eventually want to run a 3s in one just to see what gains I get from it. But i run 2s on all my crawlers at the moment.

      about 1 month ago
    • Will P
      Will P

      Would a leaf spring kit be able to work on her somehow? As well as where do I buy parts such a tires and batteries

      about 1 month ago
    • Will P
      Will P In reply to Will P

      @RunThatRC can you post a link to all the extra parts needed took to a hobby store and been looking online I cant find anything..maybe upload a video to make all this work ?

      about 1 month ago
    • RunThatRC
      RunThatRC In reply to Will P

      @Will P lucky! My neighbor had a nice one he fabricated all his roll bars, sliders, bumpers and rear tire and gas container mounts/carriers. So solid they dont rattle or make a noise offroad. I want one but a good one is 💸

      about 1 month ago
    • Will P
      Will P In reply to Will P

      @RunThatRC sweet yeah used to working on full sized 40 series so looking forward to building a small one

      about 1 month ago
    • RunThatRC
      RunThatRC In reply to Will P

      I'm excited for you. When u get the package and pick it up your gonna think they shipped you 4 wpl trucks lol. It's a hefty package and a long fun build!

      about 1 month ago
    • Will P
      Will P In reply to Will P

      @RunThatRC thank you so much man great chanel cant wait to see more of the c34km while I wait for mine

      about 1 month ago
    • vander82
      vander82

      Wondering if D90 body and wheels would fit on this one. I think you have a D90 too. What do you think. I like Toyotas, but Defenders are hot too!

      about 1 month ago
    • RunThatRC
      RunThatRC In reply to vander82

      Might have to trim it but i see it working! I have an older video of the c24 chassis on a d90. But the d90 is good. Just add the metal upgrade kit with metal driveshafts add wheel weights and your good to go! Probably cost you the same but without having to cut and mod things imho.

      about 1 month ago
    • Danny Evans
      Danny Evans

      Great job, like always.....Bash on young man....👍👍🏁🏁

      about 1 month ago
    • RunThatRC
      RunThatRC In reply to Danny Evans

      Will do! Thanks for the compliment! I wish I was a young man. Well not really lol.

      about 1 month ago
    • Andrew Miller
      Andrew Miller

      First off thanks for the great content, your channel got me interested in WPL. I wanted to get into crawling and was really unsure what to start with. My budget was around $200, but evrything out there seemed too cheap/unrealiable or too expensive. Happy to say I ended up buying a c24K and love it! Budget freindly with endless upgrades/modifications to keep me busy. Out of the box I installed 2 speed motor/transmission which came with the WPL transmitter (upgraded version). I also did the OP metal upgrades out of the box. I'm running a turnigy 800 mah lipo on a 20A esc w/brake, and all that because of your videos. Total with shipping I am roughly at $130, which may seem like a lot but that includes EVERYTHING: c24 kit, OP metal upgrades, battery, charger, transmitter/receiver, 2 spd gearbox, esc and shipping. Got great info from your 2 speed gearbox "tips and tricks" and just a really good idea of how these kits work in general from the content on your channel so thank you! Made it super easy to decide what I wanted (upgrades, kit, battery, esc, etc..) and felt comfortable buying my truck because I felt like you represented what to expect good/bad out of the box. Keep the videos coming. Look forward to running video of your new c34km, and c34k! Thinking that will be my next truck. Might have to paint it pink for my daughter so I can get her addicted rc crawling too!

      Cheers! Thanks again!

      about 1 month ago
    • RunThatRC
      RunThatRC In reply to Andrew Miller

      yes start them young! Thanks for your support and glad I could help! Looks like the wpl modding bug got you too. Sorry lol. I enjoy these things! They are like pokemon. Gotta catch them all! LoL

      about 1 month ago
    • Toysportal TV
      Toysportal TV

      the packaging is scary, they should invest more on the packaging it looks pretty bad, because some of my friend didn't so lucky the body is damage :(

      about 1 month ago
    • RunThatRC
      RunThatRC In reply to Toysportal TV

      Yeah when you receive a package like that it's time to cross fingers lol. Tell them to contact seller. Hope they help them out.

      about 1 month ago
    • semperatis
      semperatis

      The great thing is,that you don't need to worry about not having a drag brake on these ESC's as the reduction gear on the motor won't let the truck freewheel.

      about 1 month ago
    • RunThatRC
      RunThatRC In reply to semperatis

      Mine actually freewheels a little bit. Got the driveline super dialed no binding and good gear mesh in ring and pinion. It's pretty smooth.

      about 1 month ago
    • The foam Farmer
      The foam Farmer

      Please do a video on how to fit the 2 speed and what drive shafts you need and did that screwdriver come with the kit

      about 1 month ago
    • RunThatRC
      RunThatRC In reply to The foam Farmer

      @The foam Farmer if they do that would be great. But I think they might be too long for the 2 speed because the case is longer. We will see I guess🤞

      about 1 month ago
    • The foam Farmer
      The foam Farmer In reply to The foam Farmer

      That would be great because I just ordered the c34 metal kit and a 2 speed for a different build but when they come I might have to throw the 2 speed in it I hope the stock kit drive shafts will fit it

      about 1 month ago
    • RunThatRC
      RunThatRC In reply to The foam Farmer

      I probably will be making a video on it. It's too slow for the trail hikes I do. Hopefully sometime next week I should have a video out.

      about 1 month ago
    • model nutty
      model nutty

      when I got MN-D90 was hoping a Land Cruiser would come out, but after seeing it I'm just not as enthused, the rear wheel wells just don't seem to have enough room/height. those springs sure do have a lot more coil, is probably what's limiting the travel of shock rods. really do like the ALL METAL STUFF, center clearance+smoothness, longer drive shafts too.
      C-24 I drilled new holes for the shocks tops about 9/16" inboard of the stock location, they're tipped in at the tops instead of slightly tipped out and does allow a little longer easier travel, something that caught my eye in a HobbyDaddy video.

      looks like the C34 tires+rims are a little larger diameter? it'd make it more difficult to get a different tread pattern onto it... and speaking of, the C-14, mentioned before clipping out the "3 dot" down the center of the tread (tedious there's like 18 rows each tire!) definitely gets more bite in loose stuff, the larger single dots are lined up with the wider of the outer cleats.
      I've been mounting tires with Elmer's rubber cement, holds decent enough, easy to rub away excess and peel tires back off if/when needed. really like videos and comments with the tips and mods for improving, but this video is an unbox assemble/run stock and review of what they've done new+different, good job!

      that "deep dish" stock rim mod, used an X-acto pull saw blade here to do it, made it pretty easy job but can be done carefully with a more cumbersome hacksaw, the sections need sanding flat for joining with CA after anyway. JJRC tires... same tread pattern as the older WPL and about same hardness as the RTR tires, but different compound and more traction on hard surfaces, seems weird because they're "shinier looking". haven't tried the WD-40 bag soaking with a set of them yet (but am now! lol), and don't know if they'll change or not.
      lol there I go again with the 1000+ words :)

      about 1 month ago
    • RunThatRC
      RunThatRC In reply to model nutty

      @model nutty nice! I wonder if flexing and stretching the tire will be a better route to take with the jjrc tires? I will give that a try once my hands stop hurting from adjusting the links on this c34 to get the truck articulating how I want it! That was a couple hours of tinkering lol.

      about 1 month ago
    • model nutty
      model nutty In reply to model nutty

      about 12 hrs bagged wet they softened+swelled, decently soft, gained about 1/8" in height (JJRC's tires). think I like them better when they were harder and springier where they'd be better for a 6 axle truck like they're meant for.... so now you know!

      the older style WPL RTR tires definitely do it better with the WD-40 bagging, they stay a little firmer. their soft kit tires I'm using foam inserts that are barely wider and 1/4" smaller diameter. good soft give, then hits the foam that backs it up, robbed from spare GPtoys/Subotech 1/24 wheels that I like without the foam anyway.

      about 1 month ago
    • model nutty
      model nutty In reply to model nutty

      yup, they don't have a vent hole, and the tread pattern is a little bit tighter than the WPL tires but same. they do seem to grab more traction on hard surfaces vs WPL RTR or soft kit tires, also had some fun success with wetting tire lugs with nail polish remover (the "protein enriched" not the pure acetone)

      about 1 month ago
    • RunThatRC
      RunThatRC In reply to model nutty

      The tires are taller but the rim is still the same size so you can use the other kit tires if you wish. I think I just purchased a set of those jjrc rtr tires. They are shiny and dont have a vent hole on the rim.

      about 1 month ago
    • Just4Fun
      Just4Fun

      Nice. looking forward to 370 with 2 speed

      about 1 month ago
    • Just4Fun
      Just4Fun In reply to Just4Fun

      @RunThatRC sweet. it seems i got 370 180 and 130 motor. yeah with the 1:1 tranny its little to slow for me.

      about 1 month ago
    • RunThatRC
      RunThatRC In reply to Just4Fun

      It might have to happen sooner than later. It's fun for a crawl course but too slow to walk a trail with.

      about 1 month ago
    • Pedro Silva
      Pedro Silva

      Mine arrived today! 😁 Tomorrow assemble time, any tip for assembling?

      about 1 month ago
    • RunThatRC
      RunThatRC In reply to Pedro Silva

      Just make sure both your axle pumpkins are both on the same side closer to the passenger side. And install the shocks first like the c24/c14. Not sure of the length of the links because I just winged it but they will be a little longer than the plastic links on the other c series trucks. The last thing I can think of is dont install the 4th link on the front top passenger because it's a 3 link with panhard bar setup.

      about 1 month ago
    • Hansaka Nakulugamage
      Hansaka Nakulugamage

      Great to see you received it finally
      Great review brother 👍 you got your Toyota shirt out so it’s official 😎
      Can’t wait to get one of these bad boys

      about 1 month ago
    • RunThatRC
      RunThatRC In reply to Hansaka Nakulugamage

      it's a good one!

      about 1 month ago
    • Mel Myrtle
      Mel Myrtle

      Awesome glad to see yours is in can't wait to see more videos on it . Hopefully I'll have mine soon . Great video thanks for the entertainment.

      about 1 month ago
    • RunThatRC
      RunThatRC In reply to Mel Myrtle

      You will like this one. It's pretty cool. Definitely a step up from previous kits.

      about 1 month ago
    • Chris Jones
      Chris Jones

      I love the way you think. Everyone can have their own artistic flare for little money with these trucks.

      about 1 month ago
    • model nutty
      model nutty In reply to Chris Jones

      there's LOTS of tips tricks and budget mod videos, comments too. some are excellent, and some get you thinking "how to do it better", like putting shims behind both plastic bushings of the axle input covers.. think it was a Hoopties video where he'd just put a washer outside the internal bushing (behind the small bevel pinion) that inspired me to shim behind both bushings instead, for both better mesh and less wobble at the short shaft. newer C-14/24 kits come with the brass bevel pinions and the tan lower ratio B-36 gearbox, is a big improvement, so we do know WPL has been paying some fair attention to customer video and comment feedback.

      maybe tomorrow, maybe Monday... another C-24 kit will arrive for some chop shop action, swapping B-1 frame to make a C-24 drift (need 8t 0.5 modulus pinion direct btw, no room for 9t).
      B-1 with a C frame under it (painted black) will look a little awkward for sure, and a slammed low C-24 on the B-1 frame should be interesting.
      if it doesn't work out it'll only take a couple hours to put them both back to normal. the modified older style #316 gearbox is ready and waiting.

      about 1 month ago
    • RunThatRC
      RunThatRC In reply to Chris Jones

      Yup! That's what makes these little rigs awesome!

      about 1 month ago
    • Joel Vale
      Joel Vale

      I've got the Toyota pickup truck and the box came just like yours, but I was glad to see that it was OK, now I'm waiting for one just like yours.

      about 1 month ago
    • RunThatRC
      RunThatRC In reply to Joel Vale

      You will like this model. It's on a whole new level!

      about 1 month ago
    • Overland RC
      Overland RC

      I dig the shirt ;)
      Did you hear about the full metal 2 speed? I saw one on aliexpress and some metal gears to go in the regular 2 speed.

      about 1 month ago
    • Overland RC
      Overland RC In reply to Overland RC

      @RunThatRC sounds good!

      about 1 month ago
    • RunThatRC
      RunThatRC In reply to Overland RC

      I've seen those. Looks interesting but I haven't ruined a plastic one yet. Even my d90 brushless with WPL 2 speed still running strong. The metal gears and case aren't made by WPL unfortunately but it might be good. I have the metal gears and will have a video on them soon!

      about 1 month ago